ABB SPARE

ACS-CP-U CONTROL PANEL

ACS-CP-U CONTROL PANEL

JINT-E1C MC INTERFACE BOARD

E-FRAME 380-500V COATED

AINT-02C SP KIT MAIN INTERFACE

AINT-02C SP KIT MAIN INTERFACE

ZINT 7B1C N8205 NON RATED BCU SP MC INTERFACE BOARD

Used as main interface board in ACS880-04XT modules +P943 (R10,R11) with BCU-x2 control unit. This is NON-RATED board. PU-type and ratingID must be programmed afterwards by a ABB service engineer

JMU-02 W LATEST SW MEMORY UNIT KIT

JMU-02 is compatible only with JCU-11 control units

SB201M-C3 NA Miniature Circuit Breaker

System pro M compact SB200M Miniature Circuit Breakers are current limiting. They have two different tripping mechanisms, the delayed thermal tripping mechanism for overload protection and the electromechanic tripping mechanism for short circuit protection. They are available in different characteristics (B,C,D), configurations (1P,1P+N,2P,3P,3P+N,4P), breaking capacities (up to 10 kA at 240/415 V AC) and rated currents (up to 63A). All MCBs of the product range SB200M comply with IS/IEC 60898-1, allowing the use for residential, commercial and industrial applications.

ZINT-571 NON-RATED CCU-24 SP MC INTERFACE BOARD

FOR CCU-24 Compatible only with CCU-24 and AFTER manufacturing week 25/2017 CCU-24 software must be v2.03.0.4 or later. Used as main interface board in ACS580, ACH580, ACQ580 modules (R6-R7), where the control unit is CCU-24

ACS550 CONTROL UNIT

DS CONFIG SOFTWARE VC CODE To be used for ordering SMIO and sw for ACS550.

ABB AINT-14C

PART CODE- 68258529 AINT-14C; MC INTERFACE BOARD

CCU-24-S PACKED CONTROL UNIT

The control unit used in ACS580 R6-R11. For pre-programmed CCU-24-S with software versions see the document 4FPS10000294769 from IHMM

ABB MOTER

ABB INDUCTION MOTER IE2

CT-ERC.22 Time relay

The CT-ERC.22 is a single-function electronic time relay from the CT-C timer range. It provides an ON-delay (delay on make) function with 7 time ranges from 0.05 s to 100 h. This time relay operates with a rated control supply voltage of 24 - 48 V DC / 24 - 240 V AC and has a 2 c/o (SPDT) output with contacts rated at 250 V / 4 A.

PSTX250-600-70 Softstarter

The softstarter PSTX250-600-70 has a rated maximum operational current of 250 A with an operating voltage span from 208...600 V AC. The rated control voltage is between 100...250 V AC at 50/60 Hz. PSTX features a three-phase control soft start and stop through a voltage or a torque ramp. It has built-in bypass for easy installation and energy saving. A RUN, TOR and Event signal is available from relay outputs in NO (normally open state). The PSTX has functions such as current limit, kickstart, analog output, EOL, motor heating and pump cleaning. PSTX also features features jog, braking, stand-still brake, diagnostics, sequence start and emergency/fire pump mode as standard.To interact with PSTX, it has a detachable full graphic display with IP66 and 4x outdoor rating. There are four ways to communicate with PSTX. It can be done by hardwire inputs Start/Stop/Reset of fault, and by three programmable digital inputs. Another popular option is the built-in Fieldbus communication Modbus RTU and incl optional ANYBUS modules with every major protocol such as for example Profinet, Profibus, Modbus TCP, Ethernet IP and others. Another way to communicate with PSTX is to use an external adaptor and a Fieldbus plug. PSTX is the complete alternative for any motor starting application. Its suitable for medium to large-sized three-phase motors with nominal currents from 30...1250 A inline connection or 52...2160 A inside delta connection. Typical applications are, for example, pumps, fans, compressors, and conveyors.

BGAD-02C ADAPTER BOARD

2,2Ohm TURN ON 3Ohm TURN OFF

CONTR PAN CAB RMIO-02/ADPI-01 DATA CABLE

L=1500MM,SCREENED,EXTRA ISOLATION(L=1 L=1500MM, SCREENED, EXTRA ISOLATION (L=1

BGAD-11C PRIMEPACK ADAPTER BOARD

PRIMEPACK ADAPTER BOARD

ZPOW-7B1C POWER SUPPLY BOARD

190W / 250...1330VDC If BPOW-01C board is replaced with ZPOW-7B1C board then the BGDR-01C (3AUA0000074145) board revision must be checked. It must be revision K or later.

WIRE HARNESS SET

RYE STANDARD KIT; WIRE HARNESS KIT

POWER RESISTOR VHPR 80 HX 3R3 K SKN POWER UNIT

POWER UNIT

Single Phase ABB Gate Driver Board TYPE- JGDR-G1C

Single Phase ABB Gate Driver Board TYPE- JGDR-G1C

BFPS-48C POWER SUPPLY BOARD

POWER SUPPLY BOARD

ABB Motors

ABB AC MOTER PRODUCT CODE-3GBA071310-BDC

OTAC-01-KIT PULSE ENCODER INTERFACE

PULSE ENCODER INTERFACE

D1751S24B6CZ-16 FAN AXIAL

24Vdc 1,8A IP21 BRUSHLESS AXIAL FAN Fan types in production: Ebmpapst 6314HR-900 Japan Servo D1751S24B6CZ-16 Delivered type as a spare part: D1751S24B6CZ-16 which is backwards compatible with older drives // 08/2007

ABB JINT-G1C CARD

JINT-G1C R8-FRAME 380-500V COATED; MAIN CIRCUIT BOARD JINT

FAN ACS 880 R6/R7 IP55 Axial Fans

ABB BRAND FAN

Moulded Case Circuit Breaker

T4L 250 PR223EF In=250A 3p F FC 1000VAC + KIT MP T4 W 3p + AUX-E-C 1Q 1SY T4-T5 >INTEL.x SER.COMM. + ADP 6pin AUX T4-T5-T6 P/W + FLD T4-T5 W + X3 FOR PR222DS/P/PD T4..T6P/W >AL.SIGN-L + X4 FOR PR222DS/P/PD T4..T6 P/W > N EXT

Electronics Training Kit JMU-02 W LATEST SW

GOOD

APOW-01C POWER SUPPLY BRD

COATED POWER SUPPLY BRD APOW-01C

NDIO-02 OPTION/SP KIT DIGITAL I/O EXTEN

NDIO-02 DIGITAL I/O EXTENSION

Bgad-01c card

BGAD-01C,3AUA0000078108

DATA CABLE

CONTR.PAN.CAB.RMIO-02/ADPI-01

NDCU-52CK W/O SOFTWARE DRIVE CONTROL UNIT

NAMC-51C+NIOC-02C+NDCO-03C PLEASE NOTE THAT THE APPLICATION SOFTWARE IS NOT INCLUDED! THE NAMC BOARD TO BE ORDERED SEPARATELY! LATEST SW VERSIONS: ASXG6040M/F MASTER/FOLLOWER SW / AMXG6050 SYSTEM SW ASXG6040STD STANDARD SW / AEXG6110 EXTRUDER SW ASXG6040STEPU STEP-UP SW / AHXG6010 PUMP AND FAN SW

PPCS BRANCHING UN NPBU-42C PPCS BRANCHING UNIT

CH NPBU-42 NPBU-41 HAS BEEN REPLACED WITH NPBU-42 (63982784). CONNECTION CABLE OF NPBU-41 HAS CONNECTOR WHICH HAS TO BE CUT OFF WHEN REPLACING NPBU-41 WITH NPBU-42. CONNECT WIRES DIRECTLY TO THE SCREW CONNECTOR OF NPBU-42. USED IN PARALLEL CONNECTED ACS600 AND ACS800 DRIVES. IF USED WITH STANDARD SW. ASXR7140 OR NEWER, NPBU MUST BE SELECTED MANUALLY AFTER SW LOAD. JN180405

A50-30-00 690V 60Hz Contactor

A50 contactors are mainly used for controlling 3-phase motors and generally for controlling power circuits up to 690 V AC / 1000 V AC or 220 V DC. The contactors can also be used for many other applications such as isolation, capacitor switching, lighting. The A... series 1-stack 3-pole contactors are of the block type design. - Main poles and auxiliary contact blocks: 3 main poles, front and side-mounted add-on auxiliary contact blocks - Control circuit: AC operated with laminated magnet circuit - Accessories: a wide range of accessories is available.

ABB SOFT STARTER

SOFT STATER

SKN20/16 DIODE

SKN20/16; DIODE

PSR25-600-70 Softstarter

The softstarter PSR25-600-70 has a rated maximum operational current of 25 A with an operating voltage span from 208...600 V AC. The rated control voltage is between 100...240 V AC at 50/60 Hz. PSR features a two-phase control soft start and stop through a voltage ramp. It has built-in bypass for easy installation and energy saving. A RUN and a TOR signal is available from a relay output in NO (normally open state). The start/stop ramp and time is easy to set by three potentiometers on the front. PSR is often used in combination with a manual motor starter (MMS) from ABB, so mechanical connection kits are available. Another popular option is Fieldbus communication, which can be enabled by an external adaptor and a Fieldbus plug. The PSR range is our most compact softstarters with basic functionality and values. They are suitable for small three-phase motors with nominal currents from 3...105 A and can manage up to 100 starts per hour. Common applications are, for example, pumps, fans, compressors, and conveyors.

G2 MAIN FAN 48V

G2 MAIN FAN 48V; FAN, AXIAL

A50-40-00 660-690V 50Hz Contactor

A50 4-pole contactors are mainly used for controlling non-inductive or slightly inductive loads (i.e. resistance furnaces...) and generally for controlling power circuits up to 690 V AC and 440 V DC. The contactors can also be used for many other applications such lighting... The A... series 4-pole contactors are of the block type design. - Main poles and auxiliary contact blocks: 4 N.O. main poles, front and side-mounted add-on auxiliary contact blocks - Control circuit: AC operated with laminated magnet circuit - Accessories: a wide range of accessories is available.

R8 IGBT WIRE SP K 3 PCS RIBBON CABLES

R8 IGBT WIRE SP K 3 PCS RIBBON CABLES; WIRE HARNESS KIT

PSE60-600-70 Softstarter

The softstarter PSE60-600-70 has a rated maximum operational current of 60 A with an operating voltage span from 208...600 V AC. The rated control voltage is between 100...250 V AC at 50/60 Hz. PSE features a two-phase control with a soft start and stop through a voltage or a torque ramp. It has built-in bypass for easy installation and energy saving. A RUN, TOR, and Event signal is available from a relay output in NO (normally open state). The PSE has functions such as current limit, kickstart, analog output, EOL, underload, and locked rotor protection. To interact with PSE, it has an Illuminated display that uses symbols to become language neutral. As an option, you can add an identical external keypad with a rating of IP66. There are three ways to communicate with PSE. It can be done by hardwire inputs Start/Stop or by Reset of fault. Another popular option is the built-in fieldbus communication Modbus RTU. You can also use an external adaptor and a Fieldbus plug. PSE is a true general purpose softstarter. Its a perfect balance between high starting capacity and cost efficiency. Very suitable for small to medium-sized three-phase motors with nominal currents from 18...370 A. Typical applications are, for example, pumps, fans, compressors, and conveyors.

10A BS type fuse link size-F1

ACX550 FAN KIT 4

ACX550 FAN KIT 4

RHE XT1-XT3 F/P STAND. RETURNED

ROTARY HANDLE OPERATING MECHANISM STANDARD ADJUSTABLE DEPTH L=500 MM WITH PADLOCK DEVICE AND DOOR INTERLOCK FOR C.BREAKER FIXED-PLUG-IN XT1-XT3

BGAD-01C ADAPTER BOARD

BGAD-01C; ADAPTER BOARD

CURRENT TRANSDUCE LF 505-S/SP13 3PCS SP ELECTRICAL KIT

ZINT-571 and N8205 NON-RATED ZCU SP MC INTERFACE BOARD

ZINT-571 compatible with ZCU Compatible only with ZCU-12. Older drive with ZCU-11,then replace also ZCU-11 + ZMU-01 to ZCU-12 + ZMU-02.

ZINT-592 and N8205 NON-RATED ZCU SP MC INTERFACE BOARD

ZINT-592 compatible with ZCU Compatible only with ZCU-12. Older drive with ZCU-11,then replace also ZCU-11 + ZMU-01 to ZCU-12 + ZMU-02

ZINT-592 NON-RATED CCU-24 SP MC INTERFACE BOARD

This is NON-RATED board. PU-type and ratingID must be programmed afterwards by a ABB service engineer (IHMM access required)

BGDR-01C GATE DRIVER BOARD

BGDR-01C must be rev K or newer when ZPOW-7B1C is used.

CBH 165 C 4 10R RESISTOR

7400 J 10 Ohm

BGAD-12C PRIMEPACK ADAPTER BOARD

PRIMEPACK ADAPTER BOARD

BGAD-13C PCB

PRIMEPACK ADAPTER BOARD

FAN ACS880 R6/R7 IP55 LONG-LIFE FAN AXIAL

The single fan used in ACS880-01 IP21/IP55 frames R6 and R7 ACS580-01 IP21/IP55 frames R6 and R7 ACH580-01 IP21/IP55 frames R6 and R7 ACQ580-01 IP21/IP55 frames R6 and R7

BINT 12C and N8205 NON-RATED BCU SP MC INTERFACE BOARD KIT

BINT-12C compatible with BCU Used as main interface board in ACS880-104(R8i) and ACS880-304+A118 (D7T, D8T) This is NON-RATED board. PU-type and ratingID must be programmed afterwards by a ABB service engineer (IHMM access required) Compatible with INU, ISU, ISU 2Q, DSU, RRU, DBU, DDC firmwares FW2.3 or later. Multiple programming allowed . For pre-loaded BINT-12C board with correct PUtype and RatingID use xINT configurator code 3AXD50000155477

SB201M-C4 Miniature Circuit Breaker

System pro M compact SB200M Miniature Circuit Breakers are current limiting. They have two different tripping mechanisms, the delayed thermal tripping mechanism for overload protection and the electromechanic tripping mechanism for short circuit protection. They are available in different characteristics (B,C,D), configurations (1P,1P+N,2P,3P,3P+N,4P), breaking capacities (up to 10 kA at 240/415 V AC) and rated currents (up to 63A). All MCBs of the product range SB200M comply with IS/IEC 60898-1, allowing the use for residential, commercial and industrial applications.